PT 500c Manual, Motorized Pan and Tilt Head with Automatic Remote Control from 21best.com.

		Book mark us now, press Ctrl and D at the same time.
	Manual for the PT500c Indoor Pan/Tilt head Motor. Medium Duty indoor Pan & Tilt head.

Return to the Pan Tilt Page - Click Here

Allows you to move the camera up & down, right & left over a wired hand held remote control.

Manual for the PT 500c Pan/Tilt Motor.

All text version of the PT 500c Pan Tilt Motor manual.

IMPORTANT SAFEGUARDS:

CAUTION: Risk of Electric shock. Do not open.
CAUTION:To reduce the risk of electrical shock. Do not open covers.
No user serviceable parts inside. Refer servicing to qualified service personnel.

GRAPHIC SYMBOLS EXPLANATION:

The lighting flash with a arrowhead symbol, in an equilateral triangle, is intended to alert the user. There is uninsulated"dangerous voltage" presence near the product's enclosure which may be a risk to people.

The exclamation point within an equilateral triangle is to alert the user to reference of the important operating and maintenance (servicing) instructions.

CONTENTS:
Pan/Tilt Unit, Installation,Wiring of Unit, Inverted Mounting.................. Page 2
Adjusting Limit Stops ...............................................................................Page 3
Maintenance, PT 500c Indoor Pan/Tilt.. .................................................Page 4

Page 1.

PT 500c Indoor Pan/Tilt Unit

1. INSTALLATION:
The PT 500c is intended to be wall mounted with a
Heavy duty aluminum indoor / outdoor bracket # OCHWMTs.

Installation of the pan and tilt drive to the wall mount requires one steel 1/4-20 screw, which is supplied with the wall mount.

Lift off the tilt plate by removing two screws one on either side of the tilt plate.

Secure the PT 500c pan tilt motor to the tilt plate using one screw inserted through the middle hole of the tilt plate into the threaded hole on the bottom center of the pan tilt motor. Return the tilt plate to the original position use the two screws that were remover earlier.

Aim the camera in the desired direction then tighten three screws, two on tilt plate and one on the bottom for the pan joint.

2. WIRING OF UNIT:
Fabricate the interconnecting cable in accordance with Figure 1 for proper operation:
Cable Assembly Diagram:
1. Auto
2. Common
3. Tilt Down
4. Tilt Up
5. Scan Right
6. Pan Left.

3. INVERTED MOUNTING:
When the unit is mounted in the inverted position, the left right directions are reversed for manual operation. This must be corrected when wiring the cable between control unit the pan tilt drive. Simply Reverse leads going to terminals 3 and 4.

Page 2.

4. ADJUSTING LIMIT STOPS:
After cable is installed and unit has been mounted. Proceed as follows:
1. Plug control unit into a 117 VAC to 24 VAC source. Be sure auto switch is in the OFF position.
2. To adjust pan limit stops (see Figure 2), loosen screws securing both stops (1) and (3) to unit. Slide stops around unit to desired locations and secure by tightening screws.

Legend for pan tilt diagram.
1. Right Pan Limited Stop.
2. Limit-Switch Actuator.
3. Left pan Limited Stop.
4. Camera Mounting Plate.
5. 4-conductor cable for video signal.
6. Video Output.

Page 3.

5. MAINTENANCE:
This pan and tilt drive requires no lubrication or maintenance for the life of the unit. If the unit fails to function, turn it off and check the fuse on the control unit. Replacement fuse values are given in the instructions supplied with the control unit

Page 4.

SPECIFICATIONS:
Angular travel..........................................Pan:350, Tilt +- 60.
Limit Stop................................................Externally adjustable.
Speed......................................................Pan 5 Degrees/ seconds, Tilt 3 Degrees/ seconds.
Load Rating.............................................Pan 7 KGs, Tilt 4 KGs.
Duty Cycle................................................Pan continuous, Tilt: intermittent duty.
Input Voltage............................................24 VAC / 120 VAC 50 Hz / 60 Hz.
Motor Output............................................6 Watts.
Normal Operating Current......................24 VAC at 0.083 Amp
Cable Requirement................................Six-conductor unshielded.
Operating temperature...........................-10 degrees F to +140 degrees F, -25 C to +60 C.
Construction ............................................Aluminum and plastic.
Finish........................................................Off white baked enamel finish.
Dimensions............................................. 7" high, 6.5" wide, 5" deep.
Weight ......................................................4 Pounds. 1.9 KGs.

Pan Tilt Zoom (PTZ) CCTV cameras are affordable and offer better performance then ever.
Pan Tilt Zoom surveillance cameras are used by Government, large corporations, casinos and consumers. Other uses include Mast Aerial Photography.
PTZ cameras rotate horizontally through 360 degrees, vertically through 90 degrees and have motorized optical zoom lenses. A camera turret or motorized swivel is similar to a pan-tilt head.
Pan Tilt movement can be very fast and is controlled through a wired (or wireless) connection, by the mating controller.
PTZ cameras are often mounted in domes, outside dome cameras are weatherproofed, heated and cooled.

About us, 21best.com & UHF Associates.
Since 1971, UHF Associates & 21best.com has been committed to providing quality products and services to professionals and consumers, contractors, dealers, retailers, systems Integrators, Business-To-Business (B to B), distributors and original equipment manufacturers (OEMs). Our goal is to deliver the best possible combination of products, service and pricing. We are committed to continually offering our customers a variety of quality products at low prices. We pride ourselves on offering honesty, value, fast service and customer satisfaction, along with technical information and friendly customer service. We offer a "No Hassle Return Policy". Our best source of new business is from customer referrals.
Voice... 707.584.7844
Fax ..... 707.584.5733